Wednesday, July 04, 2012

The Fix

Some of you might remember the counted thread band sampler round robin that I entered into way back in late 2006. Well, this was mine as it was returned to me. You can read my thoughts about this in this post.

 I have a motto that "everthing is fixable" (well almost everthing) and I have been deliberating on this one for a while. Now has come the time to share how I fixed my sampler.


Step 1. Identify the problem. In this case it was 4 broken threads in the fabric.




Step 2. Mark with thread where the broken threads are so they would be easilly found when required.

Step 3. Carefully remove the stitching. Appologies to the lady that did the stitching but it had to come out so I could get to those broken threads.I had to use my magnifier and  good light so I didn't do any more damage. The unpicking left a few holes from the stitching, but these will come out later either just with handling or by easing the threads back in place with a needle.

Step 4. Carefully un-weave (is there such a word?) the broken thread back to an anchor point. In this case the anchor point is the buttonhole stitch of the hardanger band. Care muxt be taken not to break the thread as it is removed as we need as much length  as possible. In this case I had only a few mm.

Step 5. Turn the work to the wrong side .

Step 6. Finish the end under some anchoring stitches. In this case the end was far too short to thread into a needle so I pulled it under with  a fine crochet hook. Ideally I would have liked to have done some double stitching in under that buttonhole stitching but the end was far to short for that. I'll settle with it just tucked underneath.

Step 7. The other end of the broken thread also has to be removed back to an anchor point. This was my initial delema as to where to take it back to. There was a  band of blackwork which wasn't really the best anchor point. I could have used it if I was desperate, but Mandy had kindly left me some space to work with so I worked a row of satin stitch to give me an anchor point. The row of satin stitch will be decorated at a later date.

Step 8. This time it was easy to to put that fabric thread into a needle & anchor it under the satin stitching.

Step 9.To replace that broken thread that I had removed, I took a thread from the side of the fabric. I'ts the same as what I just took out, only in one length, not broken.


Step 10. After threading that side thread into a needle, I anchored the end in underneath the buttonhole stitching.

Step 11. Then I very carefully wove it into the space that was vacated by the broken thread. Care had to be taken to go under and over in the right places to keep the weave correct.

Step 12. There was more anchoring to do at the other end once I had woven that thread back in.

This is that one broken thread all fixed. The weave is correct but my tension isn't the same as the original, it shows as a pulled thread. Hopefully over time with some handling, the fabric threads will work themselves around and it will be less noticeable. Having some stitching over the top will certainly help, but that is for another day. It is certainly better than no holes. In the process of fixing this one, I found another two, that makes six broken threads in all. Now to fix the other five (and any more that I find) and to think about what will go in the space.

At this point I would like to add that this fix is not suitable fo all mistakes. Each error has to be assessed in it's own surroundings to work out which is the best and least noticable way to.

Three cheers to my motto -  "Anything is Fixable" . Hip, hip hurrah.

2 comments:

Mandy said...

Thanks for such a clear demonstration on how to fix this kind of problem. Very useful. I look forward to seeing the stitching you put in this area.

Linda said...

I knew you'd have to end up doing this Jenny, and good for you to finally get to it. I've had to 'reweave' after a cutting disaster in Hardanger, and know the degree of difficulty. Great photos, thank you.